Repair TipsLocal Guides
Why does my toilet keep running after flushing
A toilet that keeps running after flushing is almost always a worn flapper, a misadjusted fill valve, or a stuck float. Here is how to diagnose and fix it in Rockville.

Your toilet keeps running after flushing because the flapper is not sealing against the flush valve seat, or the fill valve is not shutting off when the tank reaches its set level. Those two failures account for roughly 9 out of 10 running toilets we see in Rockville, Maryland. The rest are float problems, a stuck chain, or a fill tube that slipped out of the overflow pipe.
Below we break down each cause, walk through the fixes, and give you real 2026 pricing for the area so you can decide whether to handle it yourself or have us come out.
Why does my toilet keep running after flushing in Rockville MD?
A running toilet in Rockville MD is a toilet that continues to release water into the bowl or down the overflow tube after the flush cycle should have ended. That constant trickle is the sound you hear between flushes. It is not normal, and it is not harmless.
Most Rockville homes were built between the 1960s and the 2000s, and the toilets in them have rubber parts that age on a predictable schedule. Chlorine and chloramine in the Washington Suburban Sanitary Commission water supply break down rubber flappers in 3 to 5 years. After that, the flapper warps, curls at the edge, or develops a mineral crust that keeps it from seating. Water leaks past it into the bowl, the tank level drops, the fill valve kicks on, and the cycle repeats every few minutes.
If you have ever searched for a toilet repair rockville md company at 9 p.m. because you can hear the tank refilling from the bedroom, you already know how loud a small leak can be.
The five parts that cause a running toilet
Every running toilet traces back to one of five components inside the tank. Here is what each one does and how it fails.
1. The flapper
The flapper is the rubber seal at the bottom of the tank. It lifts when you press the handle, then drops back down to hold water in the tank until the next flush. When it hardens or warps, water seeps past it 24 hours a day. This is the single most common cause we find on service calls.
2. The fill valve
The fill valve (sometimes called a ballcock) refills the tank after each flush. It shuts off when the float reaches the set level. A diaphragm inside the valve wears out after 5 to 10 years, and the valve stops closing completely. You will hear a faint hiss that never stops.
3. The float
Older toilets use a round ball float on a metal arm. Newer ones use a cup-style float that slides on the fill valve shaft. If the float is set too high, water pours into the overflow tube continuously. If it is cracked and taking on water, it sinks and never triggers shutoff.
4. The flush valve seat
The seat is the rim the flapper rests on. Minerals in Rockville's water supply build up on that rim over time, creating a rough surface that no flapper can seal against. You can feel the grit with a fingertip.
5. The chain and handle
A chain that is too long can get caught under the flapper and hold it open. A chain that is too short will not lift the flapper far enough for a full flush, which leads to double-flushing and a tank that never quite settles.
How to stop my toilet from running in Rockville Maryland
You can stop a running toilet in about 20 minutes with a few basic tools if the problem is the flapper or the chain. Here is the sequence we walk homeowners through on the phone.
- Shut off the water. Turn the oval valve behind the toilet clockwise until it stops. Flush once to drain the tank.
- Lift the tank lid and set it somewhere it cannot fall. A cracked lid costs $60 to $120 to replace.
- Check the chain. It should have about half an inch of slack. If it is tangled or caught under the flapper, fix that first and test.
- Look at the flapper. Run a finger along the rubber edge. If it feels stiff, curled, or gritty, replace it.
- Check the water level. It should sit about 1 inch below the top of the overflow tube. If it is at or above the tube, adjust the float down.
- Turn the water back on and watch a full cycle. If the tank goes quiet and stays quiet for 10 minutes, you fixed it.
If the tank still refills on its own after all that, the fill valve or the valve seat is the problem. Those are worth replacing together - a flapper and fill valve kit runs $15 to $30 at any Rockville hardware store, and doing both at once saves you a second teardown.
One more thing worth checking while the lid is off: look at the supply line and the shutoff valve behind the tank. If either is corroded or weeping, that is a separate issue and one our team handles on leak detection rockville MD calls all the time.
How much does it cost to fix a running toilet in Rockville MD?
Typical 2026 pricing in the Rockville area runs $150 to $275 for a standard running toilet repair, including parts and labor. That covers a flapper replacement, a fill valve replacement, or both.
Here is how the numbers break down:
- Flapper replacement only: $95 to $150
- Fill valve replacement only: $125 to $185
- Flapper and fill valve together: $150 to $275
- Flush valve seat resurfacing or replacement: $200 to $350
- Full toilet rebuild kit (all internal parts): $225 to $400
If the toilet is 20 years or older and the porcelain is in good shape, a full rebuild is usually the better call than replacing the fixture. A new toilet installed runs $350 to $700 depending on the model, plus disposal of the old one. We quote the price before we start, so you know the number before any work begins.
For homeowners in Plumbing Rockville md in King Farm, where most of the housing stock went up between 1998 and 2005, we are often replacing the second or third flapper on the same toilet. The original builder-grade parts simply do not last.
Can a running toilet increase my water bill in Rockville MD?
Yes, and faster than most people expect. A toilet that runs continuously can waste 200 gallons a day - roughly 6,000 gallons a month. At WSSC Water's 2026 rates, that is $40 to $90 added to your quarterly bill, depending on your tier.
A slow flapper leak that only runs a few minutes per hour still wastes 30 to 50 gallons a day, which is $10 to $25 per quarter. Small enough to ignore, until you see four quarters of it stacked up.
Here is a quick test that takes 10 minutes and costs nothing. Write down the meter reading at the street before bed. Do not use any water overnight. Read it again in the morning. If the number moved, you have a leak somewhere - and a running toilet is the most common culprit.
If the meter test points to a leak but the toilet is not the source, our water leak detection rockville md service can pinpoint it without tearing up walls or floors.
Common mistakes we see on running toilet repairs
We get called to fix a lot of DIY repairs that almost worked. Here are the patterns.
- Replacing the flapper without cleaning the seat. A new flapper on a mineral-crusted seat will leak within weeks. Scrub the seat with a scouring pad or fine sandpaper first.
- Buying a universal flapper that does not match the toilet. Flappers are not one-size-fits-all. Bring the old one to the store or check the model number inside the tank lid.
- Over-tightening the fill valve nut. Plastic threads crack easily. Hand-tight plus a quarter turn is enough.
- Adjusting the float without checking the overflow tube height. If the tube is set too low, the tank will overflow into the bowl no matter where the float sits.
- Ignoring a corroded shutoff valve. If the valve behind the toilet will not turn or is weeping, you have a bigger problem than the flapper.
One more: do not pour bleach tablets into the tank to "clean" the running parts. Those tablets are the number one cause of premature flapper failure we see. They eat the rubber.
When to call a professional
Call us when the tank still refills after you have replaced the flapper and adjusted the float, when the shutoff valve will not close, or when you see water on the floor around the base of the toilet. Those point to problems below the tank that need a plumber's tools and a plumber's eye.
We also get called when a homeowner has tried two or three flappers and the toilet keeps running. At that point the valve seat is the issue, and reseating or replacing it means pulling the tank. That is a 45-minute job for us and a frustrating afternoon for most homeowners.
Our team handles Plumbing Rockville md in Twinbrook and the surrounding neighborhoods every week, and we carry the common flappers and fill valves on the truck so most repairs are done in one visit.
Frequently Asked Questions
Why does my toilet keep running after flushing in Rockville MD?
The flapper is not sealing, or the fill valve is not shutting off. In Rockville's water, rubber flappers typically fail in 3 to 5 years. A mineral-crusted valve seat or a float set too high will cause the same symptom.
How do I stop my toilet from running in Rockville Maryland?
Shut off the water, check the chain for tangles, inspect the flapper for stiffness or grit, and confirm the water level sits 1 inch below the overflow tube. If it still runs, replace the flapper and fill valve together - a $15 to $30 kit.
How much does it cost to fix a running toilet in Rockville MD?
Expect $150 to $275 in 2026 for a standard repair with parts and labor. Flapper-only jobs run $95 to $150. A full internal rebuild runs $225 to $400. We quote the price before we start.
Can a running toilet increase my water bill in Rockville MD?
Yes. A continuously running toilet wastes up to 200 gallons a day, or about 6,000 gallons a month. At 2026 WSSC rates that adds $40 to $90 per quarter. A slow flapper leak adds $10 to $25 per quarter.
How long can I leave a running toilet before it causes damage?
The toilet itself will not flood your bathroom, but the water waste starts immediately and the wear on the fill valve accelerates. Left for months, a running toilet can also overflow the bowl if the fill tube slips, which is when you get water on the floor.
Get help with Plumbing Rockville md in rockville
If your toilet keeps running and you would rather not spend your Saturday on it, our team can be at your door today. We diagnose the cause, quote the price, and fix it in one visit.
Call Plumbing Rockville at +1 (831) 293-1204 to schedule your running toilet repair.
